Self-Levelling Epoxy Coating

T.T Epoxy SL 300 is a three component self-levelling, solvent free epoxy, which can be used as flooring in all types of industry, workshops and warehouses. It is a high performance self-levelling & self-smoothing product, easy to apply, leaving a durable seamless surface, specially formulated as heavy-duty concrete coating for floor. The product consists of pre-weighed coloured resin and hardener components. It provides a hardwearing and abrasion resistant floor finish for basement, warehouses, industrial factories, ground floor car parks, traffic decks with no structural movement... Along a high resistance to chemicals and salts.

(Three-Component, Solvent-free)

AREA OF USES

• The product is specially designed for a wide range of heavy-duty use, with various levels of   mechanical and chemical exposure.
  
• Indoor car parks. Bridge decks.
• Traffic decking. Industrial floors.
• Car production and workshops. Food and beverage industry floors. Warehouses and storage facilities.
• Service stations and maintenance areas.
• Hospitals, laboratories, medical factory and chemical plants. Metal treatment plants.
• Machinery service areas 

SUBSTRATES

Concrete & Metal floors

ADVANTAGES OF THE PRODUCT

• Waterproof. Impermeable.
• High wear, abrasion and slip resistant surface possible.
• Odourless.
• Good chemical and mechanical resistance

SHELF LIFE / STORAGE CONDITIONS

24 months from date of production.

The product must be stored as per local storage regulations and should be kept in dry and well-ventilated location far from heat and direct sunlight.

AVAILABILITY

Available in 20 kg (Metal cans) + 10 kg of silica sand

(Packaging may vary from country to country depending on local requirements)

PHYSICAL CONSTANTS

APPLICATION DETAILS

SURFACE PREPARATION

Concrete: Remove slip agent and other possible contaminants by emulsion washing followed by high pressure hosing with fresh water. Remove scum layer and loose matter to a hard, rough and uniform surface, preferably by abrasive blasting, possibly by other mechanical treatment or acid etching. Seal surface with T.T SF epoxy sealer, as per relevant painting specification.

Over Ceramic surfaces: the surface of ceramic must be sanded and the glaze surface must be removed and make sure the surface after that is clean, dry and free from oils or grease.

Metal Surfaces: Metal surfaces must be free from oil, grease and any kinds of liquids. In addition, the surfaces must be sandblasted to reach to uniform surface then apply one coat of epoxy primer before applying the product.

PRECEDING COAT

Epoxy Sealer SF / Epoxy Sealer SF-MT

MIXING OF THE PAINT

Mix part A for three minutes to make sure that there no settlement in the paint. Pour part B over part A, mix the two parts for 2 - 3 minutes by an electric mixer with low rotation speed (< 300 rpm). Add the silica sand gradually during mixing. The epoxy must be well mixed to ensure proper chemical reaction. After mixing, keep the mix to rest for 1 min before the application.

FOR ANTI SLIP SURFACE

For anti-slip surfaces, fine sand must be spread on the top of the paint while it is still wet. The surface is allowed to cure for at least 24 hours; the excess aggregate should be vacuum cleaned from the surface then apply a 2nd coat with a medium texture roller of T.T Epoxy Top coat SF. Care should be taken to ensure that continuous film is achieved and all grains are completely covered and coated by the epoxy mixture. The optional slip resistant texture is provided by the range of the coarse sand selected

APPLICATION CONDITIONS

Use only where application and drying can proceed at temperatures above 5°C, and relative humidity is below 75%. Apply only on a dry and clean surface.

WEATHERING

The natural tendency of epoxy coatings to chalk in outdoor exposure.

SAFETY

Application should be done in a ventilated area away from any heat source. Wear protective gear for hands and eyes and avoid breathing of vapour. If mixed resin comes into contact with the skin, it should be promptly removed before hardening, followed by thoroughly washing the skin with soap and water. In case of heavy vapour inhalation, place affected person in an open-air area. In case of contact with eyes, wash thoroughly with clean water. If swallowed, do not induce vomiting. In all cases, seek medical attention. In case of fire, use CO2 foam to extinguish. Tightly seal containers when not in use, store them away from heat and carefully dispose empty ones.

REMARK

• All technical data stated in this Product Data Sheet are based on laboratory tests. Actual values may vary due to circumstances beyond our controls.
• Newly applied material should not be exposed to water and frost for 24 hours. It should not be used in rainy and fog weather under + 5 ° C